This summary of the video was created by an AI. It might contain some inaccuracies.
00:00:00 – 00:24:32
The video, presented by Modded Warfare, provides a comprehensive tutorial on disassembling and reassembling an Xbox Series X controller, mainly for replacement, customization, or repair purposes. The process begins with removing the back panels using various tools and security Torx screws (T8), suggesting an alternative flathead screwdriver method if necessary. Removal of screws, the battery compartment, and additional components like the d-pad, sticks, plastic pieces, bumpers, and rumble motors is detailed to access internal elements such as the PCB and LEDs. During reassembly, the tutorial emphasizes the importance of correct cable routing, proper alignment of internal components, and careful reattachment of parts like analog sticks, bumpers, and the casing. Modded Warfare stresses the often inconvenient design choices by Microsoft, such as the use of security screws, but ensures that viewers are equipped to achieve a fully functional reassembly, highlighting important steps and checks throughout the process. The video concludes with practical reassurances and engagement prompts for viewers.
00:00:00
In this part of the video, the presenter, Modded Warfare, demonstrates how to disassemble an Xbox Series X controller. He assures viewers that the tutorial covers how to reassemble the controller after disassembly, which is useful for tasks like replacing buttons, sticks, customization, or repairs. He starts by removing the back panels, which can be quite stiff, especially if it’s the first time doing it. He suggests using tools like plastic pry tools, guitar picks, credit cards, or even a butter knife to help pry the panels off. Once the panels are off, he points out that the screws are security Torx screws (T8), which require a specific screwdriver. If one doesn’t have a security Torx screwdriver, he explains an alternative method using a small flathead screwdriver to remove the screws in a pinch, though this is not recommended.
00:03:00
In this part of the video, the presenter explains how to remove screws from a controller, emphasizing that a small flathead screwdriver can be used in a pinch to snap off the middle security bit of a T8 screw, allowing a regular T8 screwdriver to work. The process involves removing four screws, then the battery compartment, and a final screw underneath a sticker. After removing the screws, the back of the controller can be taken off easily, revealing the internal components similar to an Xbox One controller, including PCB connections and a plastic shell. The presenter also demonstrates removing the d-pad and sticks for further access.
00:06:00
In this part of the video, the presenter discusses how to disassemble a controller to access and replace internal components. Key actions include removing plastic pieces and bumpers, which have small clips, and taking off the rumble motors inside the triggers. The presenter uses a T6 screwdriver to remove screws from the triggers, frees wires from their clips, and carefully lifts the rumble motors out. The process ensures that all wiring is loose before the final extraction of the components.
00:09:00
In this part of the video, the speaker explains how to disassemble and reassemble an Xbox Series X controller. They start by removing the first PCB using a T6 screwdriver, then unplugging the board to lift it out, revealing the rumble motors. Next, they remove additional screws to access and lift off the main PCB, exposing the buttons and the power LED. The speaker details the type of LED used (0805 or potentially 603) and removes the buttons by taking off a rubber strip. For reassembly, they first put the strip back on, place the PCB upside down, and secure it with screws, starting with the middle one for stability. Finally, they reattach the headphone jack assembly.
00:12:00
In this part of the video, the focus is on assembling electronic components. The presenter takes a PCB, aligns it on top of another, and ensures black wires underneath are not crushed. They plug in the two slots, secure the assembly with screws using a T6 Torx screwdriver, and then proceed to insert the motors. The motors require careful handling to fit past protruding plastic parts, often needing a flat head screwdriver for assistance. The wires are organized to prevent tangling or excessive tightness. Finally, the right rumble motor is installed, with specific orientation and wire positioning to ensure proper fitment and function.
00:15:00
In this part of the video, the speaker demonstrates how to properly screw and route cables for a device. They start by inserting a screw and securing it with a T6 screwdriver. Then, they highlight the importance of routing the cables correctly, showing how to place them in designated grooves to ensure everything is neat and functional. They first route the cables on one side, making sure each fits into its specific path, and then proceed to do the same on the other side, emphasizing the need for enough slack so the trigger can operate without straining the wires. Finally, they confirm all cables are secured and correctly routed.
00:18:00
In this part of the video, the person is reassembling a controller. They start by addressing some issues with the d-pad and emphasize that both the d-pad and a wire need to be positioned underneath a specific metal plate. The d-pad is aligned using a unique smaller tab at the bottom. Next, they place the wire correctly before securing the metal plate back in its position. Following this, they attach the analog sticks and ensure they are functional. Then, they proceed to snap on the right and left bumpers, aligning them with the sync button. After that, a piece covering the USB and sync button is clipped into place. The person then tackles attaching some challenging black wires using tweezers to secure them into grooves. Finally, they fit the front plastic casing onto the controller.
00:21:00
In this part of the video, the presenter demonstrates how to reassemble an Xbox Series X controller. They start by ensuring the back case is properly aligned so the battery pins are visible in the compartment. The middle screw is reinserted first to secure everything in place, followed by the rest of the screws. The presenter comments on the use of security torque screws and their annoyance with Microsoft’s non-repair-friendly design. After all screws are replaced, the buttons are checked for proper functionality. The side grips are clipped back on to cover the screws. Finally, the presenter tests the controller by inserting batteries, confirming it powers up and works. This segment shows the entire process of disassembling and reassembling the controller for repair or customization purposes.
00:24:00
In this part of the video, the presenter explains how to open the casing and reassemble it. They express hope that viewers found the information useful and encourage them to like, subscribe, and watch future videos.